Airbag impact sensor location

The Ford F, a full-size pickup truck available in rear-wheel and four-wheel drive, was introduced in Although driver side airbags became standard inthe current F also includes a passenger side unit.

Knowing your airbag sensors' location will help you troubleshoot potential deployment problems. The F's airbag sensors are located under the driver and passenger seats and inside the safety belts. The location helps the airbag unit determine when someone is occupying the seat and when the belts are fastened. In addition to frontal airbags, Super Crew and Super Cab F models are equipped with side airbags.

The side airbag sensors are located in the driver side and passenger side doors. A dealer should be notified if your airbag indicator light is deactivated when an adult occupies the passenger seat, because the unit will not deploy upon impact. You should also contact your dealer if the lamp is activated when a child safety seat occupies the seat, because it should be deactivated for safety purposes. In Februarya recall was issued on more thanto F vehicles due to the potential risk of airbag deployment failure due to a short circuit.

This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.

To submit your questions or ideas, or to simply learn more about It Still Works, contact us. Warnings A dealer should be notified if your airbag indicator light is deactivated when an adult occupies the passenger seat, because the unit will not deploy upon impact.

Recall In Februarya recall was issued on more thanto F vehicles due to the potential risk of airbag deployment failure due to a short circuit. References Edmunds. About the Author This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.Why don't fictional characters say "goodbye" when they hang up a phone?

What evidence does Coutu use to support her claim that improvisation requires resilience. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.

Hottest Questions. Previously Viewed. Unanswered Questions. Ford Ranger XL. Ford Ranger XLT. Where are ford ranger impact air bag sensors? Wiki User Hers is no in 99 and up and before 99 they are in frame rail or radiator support. MAF sensors are generally near the air cleaner box. Asked in Ford F Where is front air bag sensors for ford ranger? Their are two sensors located directly behind the front bumper along side of its mounting brackets. Answering "Where do you add freon to your air conditioner in your ford ranger?

There is no cabin air filter for a ford ranger xlt. As far as I know the force of the impact has to be great enough for the crash sensors to allow the air bags to inflate.

airbag impact sensor location

What year of Ford Ranger is this? The front driver and passenger air bags are deployed if needed by crash sensors at the front of the Rangerso unless you crash into something after being rear ended the air bags won't deploy - you should always wear your seatbelt.This code means that your vehicle was in an accident and now has crash data stored in the ACM airbag control.

This code cannot be cleared or erased with any diagnostic scan tool. It will give you the error cannot execute the routine. If tools are not removed, the supplemental restraint system SRS device may not deploy in a crash. Failure to follow this instruction may result in serious personal injury or death in a crash and possibly violate vehicle safety standards. Note: Deployable devices such as airbag modules, pretensioners may deploy alone or in various combinations depending on the impact event.

Note: Always refer to the appropriate workshop manual procedures prior to carrying out vehicle repairs affecting the SRS and safety belt system.

Note: The SRS must be fully operational and free of faults before releasing the vehicle to the customer. DTCs must be cleared from all required modules after repairs are carried out. Refer to the appropriate workshop manual for OCS system removal and installation procedure.

airbag impact sensor location

Install new OCS system rails. For a weight sensor bolt-type OCS system, inspect the passenger side floor pan for damage and repair as necessary.

Install a new seat track with OCS system weight sensor bolts. For bladder-type OCS system, inspect for damage and repair as necessary. Previous Post Next Post.Airbag impact sensors, also known as crash sensors, are important safety features for your vehicle. These sensors, located throughout your vehicle, detect a collision and trigger the airbags to go off.

They are usually found at the front of the vehicle, behind the front fender, to detect a frontal impact, and in the side columns to detect a side impact. The exact number and location of airbag sensors you have will vary from one model to another, but those are the most frequently used locations.

The purpose of your airbags is to counteract your inertia if your vehicle abruptly stops moving forward, like in a collision. Since you are not part of your car, you will continue moving forward at the same speed that the car had been going. An object in motion stays in motion unless acted upon by another force. That other force is provided by your airbags as well as your seat belts. Your impact sensors are actually activated by the same inertia that you would experience in a collision.

They contain an object that can move, like a roller or a ball, and something that holds that object somewhat weakly in place, like a spring or a magnet. If the car suddenly stops, the roller or ball will keep going forward and contact a switch, which tells a computer, the airbag control module, to deploy the airbag. When you start your car, the airbag control module will test to make sure the airbag sensor circuits are functioning correctly. As it does this check, you will see that the airbag warning light on your dashboard light up.

airbag impact sensor location

This light shows an image of a driver with a deployed airbag. If the light stays on after starting, this is your warning that something is wrong with a component in the airbag system. If the light flashes, you can read the pattern of flashes as a two-digit code. For example, if the light flashes twice, pauses, and then flashes three times, you can read that as code You can then find out what that code means for your particular vehicle.

A mechanic with a diagnostic scan tool may also be able to pinpoint the exact cause of your problem. If you do have a collision, and the airbags go off, the sensors may suffer internal damage, which will keep them from working properly in the future.

Many automakers recommend replacing your airbag sensors after any collision in which your airbags go off. Other manufacturers state that their sensors will reset themselves after a collision and need not be replaced.

Although you will need to exercise certain cautions, you can replace your own crash sensors. The most important precaution you need to take is to depower the airbag system. Then you should wait around ten minutes longer. The airbag sensor is actually designed to be able to activate for a short time after losing power.

This is so that the airbags will still work in a collision where the vehicle loses power. Once you are confident that the airbags will not activate, you can access the sensor, disconnect it, and install the new one. Depending on the exact locations of your sensors, and which one you need to replace, you may need to remove your front fender or your door column trim, or other body panels. The first step in deploying the airbag is for the system to actually realize that a crash has occurred, and this is accomplished by these sensors, so their importance cannot be overstated.

If you need an airbag sensor replacement to get your system back in working order again, you have come to the right place. At 1A Auto, we make shopping for replacement airbag sensors for your car, truck, SUV, or van easy—we're here to help you select the right part for your vehicle! Call our customer service toll free at if you have any questions about our airbag crash sensors, warranty, compatibility or to purchase, or you can buy online. In stock orders ship same day when ordered by 2pm ET. Need your part faster?

Choose expedited shipping at checkout.Most airbag crash sensors are located in the front of the vehicle.

VW Golf 5 about AIRBAG light lit /VW airbag reset/fuse 2 - brake light switch, ABS, plug towing dvcs

Domestic vehicles typically have between one and three sensors located in the crush zones at the front of the automobile. American cars have their crash sensors in the front of the vehicle and usually contain more sensors than European models. Crash sensors are designed to deploy airbags when they detect a sudden deceleration resulting from a frontal collision. The most common crash sensor used in domestic vehicles is the electromechanical sensor. This sensor has a ball and tube design located at the front of the vehicle.

When the automobile receives a hard enough jolt due to a collision, the ball comes out of the tube.

If the ball is released from the tube, the airbags deploy. After impact, the ball returns to its position. Experts recommend using a professional to reinstall or replace airbag sensors after an airbag deployment.

Home mechanics that undertake the task themselves must be certain the replacement sensor is the correct one for the vehicle. The new crash sensor must be installed in exactly the same location as the old sensor; placing the sensor in a new location may result in the airbag accidentally deploying or not deploying in the event of an accident. Home World View. What Is the Procedure for Headlamp Alignment?Airbag Crash Sensor.

From the searches, it seems that this sensor is behind the front bumper, requiring the front bumper and fenders to be removed. I have found a how to, to accomplish this, but before I remove the multitude of screws holding the front end, I wanted to ask if this sensor is the cause of this error? Is there another airbag sensor that needs to be checked, that could be easier to access? In the past I have already replaced the drivers seatbelt latch, and cleared that different code, and I have checked the wire connectors under the drivers seat.

TDI s : dweisel isn't diesel anymore! Think about this for a minute I believe what you are looking for is the sensor that is located under the carpet at the outside of the driver seat, between the seat and door jamb.

They are not easily to get to. You have the main air bag controller mounted to the right of the fuel pedal and a left and right sensor in the location I described earlier. You also have sensors in the seatbelt retractors. Sincerely, dweisel. Last edited by dweisel; February 12th, at Asking, since in my search, I have not found any pictures or directions pertaining to that sensor in a Beetle. There were some references for Jettas and Golfs. So to get to this, remove the drivers seat, probably remove the door threshold plate and pull up the carpet?

Or is it behind the rear interior panel? What would the part number be for this sensor? Originally Posted by tactdi. Thanks again, The offer of the pictures is appreciated.

Better deal than taking the entire front end off the car. Last edited by dweisel; February 13th, at TDI s : Yup, I was just about to mention where those sensors are located. IMHO, it might be worth it to pull the carpet out completely and clean it. It will take more time, but then you won't be fighting it to access the back bolts. That does mean the center console has to come out though. Past: Sold to JDSwann's Brother. Bought back by VW. It means a lot to me! Dweisel, thanks again for the description and picture, and the part numbers sent separately.

It looks like the sensor part number s are 6QA or 3BK or 3BJ Are there 2 or 3 of these sensors in the floor, or based on the photo you provided, there is one and it is located to the left of the front of the seat where the two nuts hold the front of the seat to the floor? All this really helps.

Fix SRS Airbag Code B1209 Collision Detection

The sensor is attached to a bracket, which is bolted to the floor and the sill. EDIT: dweisel posted a picture above Originally Posted by dweisel. You don't have to take the front loose.An airbag sensor is a very important safety feature on your vehicle. Without the sensor, the airbags will not know when to deploy should you be in an accident.

The airbag sensor will need to be reset whenever the airbag assembly has been repaired in anyway. Most vehicle models are set up differently. Once you have found its exact location, you are ready to get to work. Once you have done this, take the cable clamp completely off the negative terminal.

You will need to wait for at least five seconds to pass. Once it has, you are ready to reconnect the negative terminal. Make sure that the sensor reset by turning on the key switch in your vehicle.

If the airbag sensor warning light has gone out, it has been reset.

Where Are the F-150 Airbag Sensors Located?

If you find that the light has not gone out, repeat the previous steps. We welcome your comments and suggestions.

airbag impact sensor location

All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here. Toggle navigation Login Register How-Tos. How to Reset an Airbag Sensor. Written by Sage C. Reviewed by H.


1 Comment